Driver Studio 3.1 + VMWare Workstation 4.0?

Hey all,

Has anybody tried installing Driver Studio 3.1 on VMWare Workstation 4.0? Did it work for you? What video settings do you use?

Thx!

[bgrimm]

My first attempt was last night when trying to install
to a 98 vdisk.

Turns out 3.1 is 2000/XP only. The install reverts back to
2.7 if your running a 98 box.

So tonight I'll be trying it on a 2000 virtual disk and will
post the results.

-bg

[bgrimm]

Ok,

I do have Driver Studio SoftIce 3.1 running on a
Windows 2000 Pro with Service Pack 4 virtual machine.

I had a lot of trouble, ie: lockups, and finally found the
fix on vmware's support page.

It mentions adding a couple of lines to the config file
of the VM, and that is what worked for me.

Support page:
hxxp://frontline.compuware.com/nashua/kb/doc/1702.asp

I had no success with a 2k service pack 1 install.

-bg

i tried 3.01 on NT 4 SP6, which didn't accept to install
then i tried 2.7 it installed, but upon startup nt4 will bsod and reboot alone

bgrmm : Thank you, worked great! =)

Hi,
I've been trying to make it run few days, and found following; you shouldn't install vmware tools - mainly not the graphics driver. Also try different versions of sice and servicepacks - for example I managed to run Win2k SP2 and DS 2.6, but nothing else. So try and you'll see - tip: use snapshots and when anything doesn't run just revert to it.
Good luck,
least

why not try Virtual PC

[h8er]

from the Fatigue nfo

full support for AMD's 64-bit Opteron and Athlon64 processors ?
? ten new commands: SYMLINK, DEVMGR, DP, TDIR, TMKDIR, TMOVE, TRENAME, ?
? TRMDIR, TRMFILE and TVOL. ?
? SoftICE ?
? SoftICE supports kernel-mode and user-mode debugging on a single ?
? machine, on two machines using a serial line or on remote machines over ?
? a TCP/IP connection. With the release of DriverStudio 3.1, SoftICE now ?
? offers: ?
? ?
? VMware 4.0 support ?
? a new disassembly options page in "DriverStudio Config" ?
? a new user interface enhancements in the Symbol Loader. ?
? BoundsChecker Driver Edition ?
? BoundsChecker Driver Edition is an error detection tool that analyzes ?
? and detects device driver errors automatically in real time. Developers ?
? can find and fix errors as they happen, rather than hours later. Added ?
? enhancements include:

maybe only Driverstudio 3.1 works with VmWare programs...

Well I have been trying for the whole day yesterday to configure Visual Softice target on vmware and Visual Softice host on my machinebut it didn't work all too well.
My machine is displayed when I click on browse targets from driver workbench but when I click on make active, nothing is shown except an error message, 'something like unable to get ip current adress'
When I try to change the settings of the target or to configure true coverage, I get an other error message 'you do not have access permission to test" (test is my machine name.

Has anybody ever got visual softice working ? is there anything to do so as to allow acces to the machine ?

[JMI]

When are some of you folks going to figure out that the Diety invented search engines so you could find information, both here and on the net.

Again, a little careful searching, both here and on the net would lead you to:

a thread by WhoCares here, titled "VMWare Remote Debugging though Serial Port and Named Pipe" at:

http://www.exetools.com/forum/showthread.php?t=3499

and the following article on the Woodman Forums, titled:
"VMWare & Softice - Experiences, problems and solutions" at

http://66.98.132.48/forum/showthread.php?t=5806

and that's just on these two Forums. There are undoubtedly more out there.

Regards,

Of course I had first made a search on this forum and I had allready read those post but my question was mostly about Visual SoftIce and not Softice...

I wanted to debug my driver on vmware and 'remotely' accessing it with visual softice, because it seemed like the best way to get a nice and confy interface and there seemed to be some nice added features.

Regards,

There is a vmware support article describing problems with running si in a vm:

http://www.vmware.com/support/kb/enduser/std_adp.php?p_faqid=965&p_created=1049834747&p_sid=l6hHm4Mg